The design of a mobile band saw machine for longitudinal sawing of round timber
https://doi.org/10.21266/2079-4304.2023.246.320-330
Abstract
The article deals with the issues of longitudinal sawing of round timber. The aim of the research was to develop a band saw with a simplified design, with reduced metal consumption and increased mobility. The development of a new technical solution in the field of designs of band saws, not tied to a specific one workshop, but capable of sawing in different places, including cutting areas, was implemented. The article gives a detailed description of the design of the new woodworking machine and the sequence of its work when delivered to the logging site for sawing round timber. The power unit transmits torque through the driveshaft of the vehicle, the tapered gearbox, the belt gear and the bearing assembly to the stepped pulley formed by the automobile rubber tires of two different diameters that drive the band saw. The proposed design of the device of the band saw for longitudinal sawing of round timber allows to simplify the design of the machine, reduce its dimensions and makes it possible to produce longitudinal sawing away from the woodworking enterprise, increasing the mobility of the technological process. The resulting unedged lumber can be immediately transported to the consumer, which reduces the cost of production transportation of raw materials and storage of finished products.
About the Authors
E. M. Tsarev
Volga State University of Technology
Russian Federation
Russian Federation
TSAREV Evgeny M. – DSc (Technical), Professor of the Department of Forestry and Chemical Technologies, Associate Professor
424000, Lenin Square, 3, Yoshkar-Ola
K. P. Rukomojnikov
Volga State University of Technology
Russian Federation
Russian Federation
RUKOMOJNIKOV Konstantin P. – DSc (Technical), Professor of the Department of Forestry and Chemical Technologies, Associate Professor
424000, Lenin Square, 3, Yoshkar-Ola
S. E. Anisimov
Volga State University of Technology
Russian Federation
Russian Federation
ANISIMOV Sergey E. – PhD (Technical), Associate Professor of the Department of Forestry and Chemical Technologies, Associate Professor
424000. Lenin sq. 3. Yoshkar-Ola
N. S. Anisimov
Volga State University of Technology
Russian Federation
Russian Federation
ANISIMOV Nikita S. – student
424000. Lenin sq. 3. Yoshkar-Ola
I. V. Petukhov
Volga Region State Technological University
Russian Federation
Russian Federation
PETUKHOV Igor V. – DSc (Technical), Rector, Professor
424000. Lenina av. 3. Yoshkar-Ola. Mari El Republic
P. N. Anisimov
Volga Region State Technological University
Russian Federation
Russian Federation
ANISIMOV Pavel N. – PhD (Technical), Associate Professor of the Department of Energy Supply of Enterprises
424000. Lenina sq. 3. Yoshkar-Ola. Mari El Republic
References
1. Anisimov N.S., Anisimov I.S. Konstrukciya lentochnopil'nogo stanka dlya prodol'noj raspilovki v usloviyah malogo lesopileniya [The design of a band saw for longitudinal sawing in conditions of small sawmilling]. Nauchnomu progressu – tvorchestvo molodyh: sb. tr. [Scientific progress – the work of the young : collection of works]. Yoshkar-Ola, 2018, no. 3, pp. 125–128. (In Russ.)
2. Barcík Š. Experimental cutting on the table band-sawing mashine. Holz als Roh- und Werkstoff, 2003, vol. 61, pp. 313–320. URL: https://doi.org/10.1007/s00107-002-0342-9
3. Bariska M., Pásztory Z. The optimum log feed speed with bandsaw. European Journal of Wood and Wood Products, 2015, vol. 73, p. 250. URL: https://doi.org/10.1007/s001070050221
4. Chukarin A.N., Litvinov A.E., Novikov V.V. Reducing the noise and operator injuries associated with circular saws. Russ. Engin., 2017, res. 37, pp. 615–616. URL: https://doi.org/10.3103/S1068798X17070073
5. Ioras H., Nicholls T., Perkins M. et al. A review for cutting forces and stresses in circular saws. Holz als Roh- und Werkstoff, 2002, vol. 60, pp. 55–59. URL: https://doi.org/10.1007/s001070100220
6. Kremleva L.V., Malygin V.I., Lobanov N.V. Dynamic stability of band saw machines. Russian Engineering Research, 2016, vol. 36, pp. 735–740. URL: https://doi.org/10.3103/ S1068798X16090100
7. Lehmann B.F., Hutton S.G. The mechanics of bandsaw cutting. Holz als Roh- und Werkstoff, 1997, no. 55, pp. 35–43. URL: https://doi.org/10.1007/s001070050221
8. Litvinov A.E. The estimation of the impact of the «saw-saw guide» resonant frequency system on the process of cutting with band saws. Nauch. Zh. Kuban. Gos. Agrar. Univ., 2014, no. 96 (2), pp. 432–441.
9. Litvinov A.E., Kornienko V.G. Study of cutting on band saw machines. Nauch. Zh. Kuban. gos. agrar. univ., 2013, no. 9 (91), pp. 570–579.
10. Litvinov A.E., Kornienko V.G., Sukhonosov N.I., Cutting by means of band saws. Russ. Eng. Res., 2011, vol. 31, no. 1, pp. 59–61. URL: https://doi.org/10.3103/S1068798X11010151
11. Litvinov A.E., Chukarin A.N. Obzor sovremennogo sostoyaniya konstrukcij i tipov lentochnopil'nyh stankov po derevu [Review of the current state of designs and types of band saws for wood]. Mekhanika, oborudovanie, materialy i tekhnologii: sbornik nauchnyh statej po materialam Mezhdunarodnoj nauchno-prakticheskoj konferencii. [Mechanics, equipment, materials and technologies: In the collection]. Electronic collection of scientific articles based on the materials of the international scientific-practical conference]. Ed. Board: Litvinov A.E. et al., Krasnodar, 2019, pp. 142–148. (In Russ.)
12. Litvinov A.E., Kornienko V.G., Sukhonosov N.I. Technological parameters of band saws, Sovrem. Naukoemkie Tekhnol, 2007, no. 6, pp. 47–48.
13. Maksimov Yu.V., Denisov R.A., Grechishnikov V.A., Timiryazev V.A. Improving the Machining Process in Band-Saw Systems. Russian Engineering Research, 2020, vol. 40, pp. 61–63. URL: https://doi.org/10.3103/S1068798X2001013X
14. Maksimenkov A.I. Razrabotka konstrukcii i obosnovanie parametrov malogabaritnogo lentochnopil'nogo stanka dlya raspilovki lesomaterialov [Development of the design and substantiation of the parameters of a small-sized band saw for sawing timber] : abstract of a dissertation for the degree of candidate of technical sciences / Voronezh State Forest Engineering Academy. Voronezh, 2004. 20 p. (In Russ.)
15. Sviridov L.T., Ivanovsky A.V., Ivanovsky V.P. Sovremennye processy i oborudovanie v derevoobrabotke. [Modern processes and equipment in woodworking]. Monograph. Voronezh: Voronezh State Academy of Forestry, 2011. 363 p. ISBN 978-5-4218-0055-2. (In Russ.)
16. Szymani R., Trinchera L., Turner J. Use and maintenance of thin circular saws at California Ceder Products Company. Holz als Roh-und Werkstoff, 1987, vol. 45, pp. 319–322. URL: https://doi.org/10.1007/BF02605841
17. Tsarev E.M., Anisimov S.E., Pylaev N.V. Konstrukciya lentochnopil'nogo stanka dlya prodol'noj raspilovki [The design of a band saw for longitudinal sawing]. Derevoobrabatyvayushchaya promyshlennost' [Woodworking industry], 2014, no. 2, pp, 23–24. (In Russ.)
18. Tsarev E.M., Anisimov S.E., Rukomoinikov K.P., Pylaev N.V. Povyshenie effektivnosti raboty lentochnopil'nogo stanka v usloviyah malogo lesopileniya. [Improvements in band saw effectiviness under conditions of low volume sawmilling]. Vestnik Povolzhskogo gosudarstvennogo tekhnologicheskogo universiteta. Seriya: Les. Ekologiya. Prirodopol'zovanie. [Vesting of volga state university of technology. series: forest. ecology. nature management], 2017, no. 4 (36), pp. 59–65. (In Russ.)
19. Patent 2020103792 RU, Mobil'nyj lentochnopil'nyj stanok dlya prodol'noj raspilovki lesomaterialov [Mobile band-sawing machine for lengthwise sawing of timber]. / Tsarev E.M., Afonshin V.E., Anisimov S.E., Rukomoynikov K.P., Anisimov N.S., Anisimov I.S. Publ. 29.01.2020; bul. no. 22. (In Russ.)
20. Yanushkevich A.A., Shetko S.V. Raskroj breven na radial'nye pilomaterialy. [Cut logs into radial lumber]. Trudy Belorusskogo gosudarstvennogo tekhnologicheskogo universiteta. Seriya 2. Lesnaya i derevoobrabatyvayushchaya promyshlennost'. [Proceedings of the Belarusian State Technological University. Series 2. Forestry and woodworking industry]. Minsk, 1998, no. 6. pp. 94–99. (In Russ.)
Review
For citations:
Tsarev E.M., Rukomojnikov K.P., Anisimov S.E., Anisimov N.S., Petukhov I.V., Anisimov P.N. The design of a mobile band saw machine for longitudinal sawing of round timber. Izvestia Sankt-Peterburgskoj lesotehniceskoj akademii. 2023;(246):320-330. (In Russ.) https://doi.org/10.21266/2079-4304.2023.246.320-330
Views:
77
Email this article 